Cameras Ranked

What a Memory Card's Speed Marks Actually Promise

After this page you will be able to open your own camera's manual, find the row for the exact video mode you shoot, and know which two card specifications — the capacity and bus type, and the class mark — that row is asking you to buy. You will also know the two places where buying a higher mark does not help, and the one place where it fails outright.

Buy to the fastest video mode you genuinely shoot, not to the camera's headline resolution and not to the number printed on the front of the box. Your camera maker publishes a table that maps each recording format to a required card mark. That table is the answer. Everything below is how to read it, and why the number on the package is a different kind of number from the number in the table.

Every figure on this page is taken from the SD Association, the CompactFlash Association, a camera manufacturer's own manual or support page, or SanDisk's published support documentation, each cited with the page it came from and the date it was read (2026-09-22). The per-class minimum write speeds in MB/s come from SanDisk's support article, because the SD Association's own Speed Class page states the convention without printing the figures. Nothing here is ranked or scored.

The four-step version

  1. Open your camera's manual to its card section. Sony's help guide calls the page "Memory cards that can be used". Canon's EOS R5 manual uses "Cards That Can Record Movies" and points from there to "Card performance requirements (Movie recording)" in its Reference chapter. Fujifilm publishes a per-camera compatibility page.
  2. Find the row for your exact recording format and frame rate — XAVC S-I 4K, or 360 Mbps, or the S&Q row, or the 10-bit column rather than the 8-bit one — not the row for "4K" in general.
  3. Read three things off that row: the class mark (Class 10, U3, V30, V60, V90, VPG200, VPG400), the card type (SDHC/SDXC, CFexpress Type A, CFexpress Type B), and, where the row names one, the capacity tier. SDHC and SDXC are capacity tiers, not speed tiers: SanDisk gives SDHC as 4GB–32GB and SDXC as 64GB–2TB. When a row names SDXC specifically rather than SDHC/SDXC, a 32 GB SDHC card does not satisfy it even if it carries the right class mark. If the row carries a footnote marker, read the footnote too: it can raise the requirement for one particular frame-rate or bit-rate setting inside that row.
  4. Buy a card carrying that mark or higher, in that type. Higher is safe for SD class marks within one system. It is not safe for VPG, and it is not safe across SD systems — the two exceptions are in the sections below. A higher mark in the wrong type is never a substitute.

Two different kinds of number share the same package

A card marked "up to 280MB/s" and "V60" is telling you two unrelated things. SanDisk's own support article draws the line: a rated speed is the card's maximum, roughly what you would expect in typical use, while a Speed Class is a minimum based on a worst-case-scenario test. The maximum matters when you are offloading a shoot, and — inferred from the same distinction, since clearing a burst buffer is a short burst write rather than a sustained one — when you are emptying a camera's buffer. The minimum is the one that decides whether a recording runs to the end of the take. Camera manuals are written in minimums, which is why they name class marks and never quote the headline figure.

Four marking systems, and why you cannot swap between them

The SD Association defines four separate systems: Speed Class, UHS Speed Class, Video Speed Class and SD Express Speed Class. The number after the letter is the minimum writing speed. They overlap numerically — U3 and V30 are both 30 MB/s minimums, which is why Fujifilm can name either one for the same mode (inferred, from Fujifilm's wording placed beside the SD Association's class list). Do not generalise that into swapping systems on your own. The SD Association warns that a mismatched combination — its own examples are a Class 10 host with a U1 card, and a U1 host with a V10 card — will not deliver the expected write speed, in its words even though those are indicated to the same 10MB/sec write speed. Match the system your camera names, not just the number. Canon's own SD table uses all three of "SD Speed Class 10", "UHS Speed Class 3" and "Video Speed Class 60" in different rows, so this is not hypothetical.

SD card speed marks: minimum sustained write speed, and which bus family the SD Association permits each mark on. Minimum write speeds are from SanDisk's support article; bus applicability is from the SD Association. Access date 2026-09-22.
MarkSystemMinimum write (MB/s)Bus interface it may be applied to
Class 2Speed Class2Not stated on the SD Association page read
Class 4Speed Class4Not stated on the SD Association page read
Class 6Speed Class6Not stated on the SD Association page read
Class 10Speed Class10High Speed mode or faster
U1UHS Speed Class10SDR50/DDR50 or faster (UHS-I, UHS-II, UHS-III)
U3UHS Speed Class30SDR50/DDR50 or faster (UHS-I, UHS-II, UHS-III)
V6Video Speed Class6High Speed and UHS families
V10Video Speed Class10High Speed and UHS families
V30Video Speed Class30UHS family
V60Video Speed Class60UHS-II mode or faster (UHS-II / UHS-III)
V90Video Speed Class90UHS-II mode or faster (UHS-II / UHS-III)
E150 / E300 / E450 / E600SD Express Speed ClassNumber is the minimum write speed in MB/s (calculated)SD Express mode

One consequence is worth stating plainly. V60 and V90 may only be applied to UHS-II and UHS-III cards, and UHS-II onward moves data over a second row of pins. So a genuine V60 or V90 SD card always has two rows of contacts on the back. If a card shows one row and a V90 logo, something is wrong with the card, not with your camera.

The bus is a separate question from the class

SD bus interface maximum speeds, from the SD Association. UHS-I reaches its speeds on one row of pins; UHS-II, UHS-III and SD Express use two rows. All of these faster interfaces apply to SDHC, SDXC and SDUC cards. Access date 2026-09-22.
Bus modeMaximum speedPin rows
Default Speed12.5 MB/sOne
High Speed25 MB/sOne
UHS-I SDR50 / DDR5050 MB/sOne
UHS-I SDR104104 MB/sOne
UHS-II, full duplex156 MB/sTwo
UHS-II, half duplex312 MB/sTwo
UHS-III, full duplex312 MB/s and 624 MB/sTwo
SD Express, PCIe Gen.3 x1985 MB/sTwo
SD Express, PCIe Gen.4 x1 or Gen.3 x21970 MB/sTwo
SD Express, PCIe Gen.4 x23940 MB/sTwo

Here is the rule that saves money, stated only as far as its source states it. SanDisk says that a UHS-II card can be used in UHS-I and non-UHS hosts, and that the slower UHS-I or SD speed is what gets used. Putting a 312 MB/s-capable UHS-II card into a UHS-I slot does not give you UHS-II throughput; it gives you a UHS-I card that cost more. The reason to buy UHS-II for a UHS-I body is if you also want the transfer speed in a UHS-II reader, which is a workflow decision, not a recording one. That statement covers UHS-II cards. It does not cover SD Express, and neither SD Association page read here states what an SD Express card does in a UHS-II slot — so do not assume a two-row SD Express card gives you UHS-II speed in a UHS-II camera. Check the card maker's own compatibility statement for that specific card before buying one for a UHS-II body.

Your manual speaks Mbps, the card speaks MB/s — and the arithmetic never gives the answer

Camera makers quote video bitrate in megabits per second. Cards are marked in megabytes per second. Divide by eight. Then notice that in every single published case below, the maker demands more than the arithmetic asks for, and by wildly different margins.

Stated bitrate converted to average write load, beside the class the maker actually requires. The division by eight and the headroom ratios are arithmetic inferred from the bitrates and class requirements stated in the Sony, Fujifilm and SanDisk sources; the makers publish no such ratio. Access date 2026-09-22.
Mode (source)Stated bitrate÷8 = average MB/sClass the maker requires (its MB/s floor)Headroom over the arithmetic
Sony a7 IV, XAVC S 4K, normal200 Mbps25U3 / V30 (30)1.2×
Sony a7 IV, XAVC S 4K, S&Q Motion200 Mbps25V60 (60)2.4×
Sony a7 IV, XAVC S-I 4K600 Mbps75V90 (90)1.2×
Sony a7 IV, XAVC S-I HD222 Mbps27.75V90 (90)3.2×
Sony a7 IV, any mode at 60 Mbps or lower60 Mbps7.5Class 10 (10)1.3×
Fujifilm X-T5 movie360 Mbps45V60 (60)1.3×
Fujifilm X-T5 movie200 Mbps25U3 / V30 (30)1.2×
Fujifilm X-T5 movie100 Mbps12.5U3 / V30 (30)2.4×

Read the right-hand column before you trust the middle one. The required headroom ranges from 1.2× to 3.2×, and nothing in the stated bitrate predicts which you will get. The worst case is Sony's XAVC S-I HD: 222 Mbps divides to 27.75 MB/s, which a V30 card clears on paper, yet Sony requires V90 — a 90 MB/s floor, 3.2 times the arithmetic. A reader who bought from the division alone would buy a V30 card for a mode needing V90. This page cannot source why any particular margin is what it is; the makers publish the requirement, not the reasoning. Treat ÷8 as a sanity floor that rules cards out, never as a specification that rules one in. The manufacturer's table is the authority. The calculator is not.

Three real manufacturer tables, side by side

Sony's stated card requirements for the a7 IV (ILCE-7M4), from the "Memory cards that can be used" help guide page. Two rows of Sony's S&Q Motion table carry footnotes, marked *1 and *2 here and reproduced in full in the note below. Access date 2026-09-22.
ModeBitrateSD requirementCFexpress Type A requirement
XAVC HS 4K, normal recording200 MbpsSDHC/SDXC, U3 or V30 or betterCFexpress Type A
XAVC S 4K, normal recording200 MbpsSDHC/SDXC, U3 or V30 or betterCFexpress Type A
XAVC S HD, normal recording100 MbpsSDHC/SDXC, U3 or V30 or betterCFexpress Type A
Any mode at 60 Mbps or lower≤60 MbpsSDHC/SDXC Class 10 also permittedCFexpress Type A
XAVC S-I 4K600 MbpsSDXC V90 or betterVPG200 or higher
XAVC S-I HD222 MbpsSDXC V90 or betterVPG200 or higher
XAVC HS 4K / XAVC S 4K, S&Q Motion200 MbpsSDXC V60 or betterVPG200 or higher
XAVC S HD, S&Q Motion *1100 MbpsSDHC/SDXC, U3 or V30 or better *1CFexpress Type A
XAVC S-I 4K, S&Q Motion *2600 MbpsSDXC V90 or better *2VPG200 or higher
XAVC S-I HD, S&Q Motion222 MbpsSDXC V90 or betterVPG200 or higher

The one genuinely counter-intuitive row: on the a7 IV, XAVC S 4K at 200 Mbps takes a U3/V30 card in normal recording but requires V60 or better in S&Q Motion. Same format, same stated bitrate, faster card. Only the manufacturer's table shows this — and the S&Q section does not raise every row, so read the row rather than the section heading. Then read the footnote marker on the row, because Sony hangs two further requirements off asterisks. Footnote *1, on XAVC S HD at 100 Mbps in S&Q: when Rec Frame Rate is 30p/25p/24p, Frame Rate is 120fps/100fps and the recordable bit rate is 50 Mbps, Sony requires an SDXC card of V60 or higher, or a CFexpress Type A card of VPG200 or higher. So the U3/V30 cell does not cover 120fps slow motion. Footnote *2, on XAVC S-I 4K in S&Q: when Rec Frame Rate is 30p/25p/24p and Frame Rate is 60fps/50fps, Sony requires a CFexpress Type A card of VPG200 or higher and names no SD card at all, so the V90 cell does not apply in that configuration. The cell is the general case; the footnote may be the mode you actually shoot.

Canon's stated SD card requirements for the EOS R5, from "Card performance requirements (Movie recording)" in the manual's Reference chapter. This is a selection of rows from a longer table that also covers Full HD variants and time-lapse movies. A dash means Canon lists no SD option for that mode. Canon's CFexpress column, not reproduced here, reads "Refer to the Canon website" in every row, including the rows where an SD option exists. Access date 2026-09-22.
Movie recording sizeCompressionSD card, 8-bitSD card, 10-bit
8K RAWRAW / RAW (Light)——
8KALL-I——
8KIPBVideo Speed Class 60 or higherVideo Speed Class 90 or higher
8KIPB (Light)UHS Speed Class 3 or higherVideo Speed Class 60 or higher
4K 119.88 / 100.00 fpsALL-I——
4K 59.94 / 50.00 fpsALL-I——
4K 59.94 / 50.00 fpsIPBVideo Speed Class 30 or higherVideo Speed Class 60 or higher
4K 59.94 / 50.00 fpsIPB (Light)UHS Speed Class 3 or higherUHS Speed Class 3 or higher
4K, other than aboveALL-IVideo Speed Class 60 or higherVideo Speed Class 60 or higher
4K, other than aboveIPBUHS Speed Class 3 or higherUHS Speed Class 3 or higher
Full HD 59.94 / 50.00 fpsIPBSD Speed Class 10 or higherUHS Speed Class 3 or higher

Canon's table adds a dimension the other two do not. The same recording size can demand a different class depending on bit depth: 8K IPB asks for V60 at 8-bit and V90 at 10-bit, and Full HD 59.94 fps IPB moves from Class 10 to U3 on the same change. If you switch a camera to 10-bit for grading, you may have changed your card requirement without changing anything you would call a "mode". Fujifilm's X-T5 page draws its lines differently again: 360 Mbps needs V60 or better, while 100 or 200 Mbps movies need UHS Speed Class 3 or V30 or better, and Fujifilm separately recommends a UHS-II card for high-speed burst stills. Set the three makers next to each other and the point lands — Sony's 200 Mbps slow-motion row demands V60 while Fujifilm's 200 Mbps row accepts V30. The number is the same; the requirement is not. Read your own camera's table, not someone else's.

CFexpress: Type A and Type B are not interchangeable, and VPG does not ladder

The CompactFlash Association describes Type A as the smaller card using one PCIe lane, and Type B as the larger card using two lanes, allowing double the maximum speed. Type B shares its dimensions and connector with XQD. The CompactFlash Association's wording on what follows from that is permissive, not historical: it says some cameras may choose to update their XQD cameras to also support CFexpress Type B cards. That is per-body and per-firmware, not automatic. A Type B card will physically fit an XQD slot whether or not the camera supports it, so check your camera maker's firmware release notes for your exact model before buying, and do not read physical fit as support. The Association also states that at this time there are no cameras or cards that take CFexpress Type C. Type A and Type B are not grades of one thing: Sony's a7 IV takes CFexpress Type A and its manual states flatly that Type B cards cannot be used, while Canon's EOS R5 takes CFexpress Type B in one slot and UHS-II/UHS-I SD in the other.

The R5's two slots are not equivalent, and this is where a reader can waste money while following every other rule on this page. Canon's Shooting chapter lists four things that cannot be recorded to SD cards at all, with the note that pressing the movie shooting button will not start recording: RAW movies, 8K ALL-I, 4K 119.9/100.0 fps (High Frame Rate movies), and 4K 59.94/50.00 fps. No SD speed mark makes an excluded mode work. But Canon's two pages do not agree about that last item. The Shooting chapter writes it as "4K 59.94/50.00fps" with no compression method attached, while the Reference table dashes only the ALL-I variant and publishes SD classes for the rest of that mode: 4K 59.94/50.00 fps IPB takes Video Speed Class 30 at 8-bit and Video Speed Class 60 at 10-bit, and IPB (Light) takes UHS Speed Class 3 at both depths. Those rows are in the table above. Canon qualified the sibling item in the same list — it reads "8K ALL-I", not "8K" — and did not qualify this one. Do not settle that contradiction from this page. If you shoot 4K 60p on an R5, check your own body's current firmware behavior against Canon's current manual, and plan on CFexpress if you need the mode to be certain.

VPG is the CFexpress equivalent of a Video Speed Class. The CompactFlash Association defines it as a promise of minimum sustained write performance, where minimum sustained write speed means the fewest MB/s that can be written continuously without dropping frames. VPG800 promises 800 MB/s and VPG1600 promises 1600 MB/s; VPG200 and VPG400 promise 200 and 400 MB/s, inferred from the Association's stated convention that the number in the logo is the minimum sustained write speed, since its profile table is published as an image and its text prints figures only for the two newer classes. Canon's EOS R5 manual instructs using a CFexpress card that supports VPG400, or a card with ample write and read performance, for movie recording.

Here "buy higher" breaks. The CompactFlash Association states that VPG-5 is not backward compatible to VPG-4, and that a higher-performing card supporting the VPG800 or VPG1600 class will not necessarily work with a camera mode that requires VPG200 or VPG400. Within one profile, higher does cover lower — the Association gives VPG400 supporting VPG200, and VPG1600 supporting VPG800 — but across profiles it does not. If your camera asks for VPG200 or VPG400, buy a card carrying that VPG-4 logo, or one carrying both a VPG-4 and a VPG-5 logo, which the Association says indicates support for both profiles. Two further warnings from the same page: some companies may inadvertently or incorrectly use the VPG logo without actually getting their cards certified, and the Association maintains a list of VPG-certified cards you can check a part number against before buying.

When a faster card is not the fix

Canon's EOS R5 manual gives two separate reasons a recording ends on its own, and they call for opposite responses. Under "Recording and image quality", a card with a slow writing speed produces an on-screen indicator, and if that indicator becomes full, movie recording stops automatically. Separately, under the overheating displays, a red icon means the camera will turn off automatically if you keep recording, and after an automatic stop you cannot record again until it has cooled. If your recordings die at roughly the same elapsed time every session with a heat icon on screen, a V90 card will not change that.

A third cause is worth ruling out before you spend anything, because it is free. The SD Association states that write speed to a fragmented area is generally slower than sequential write speed, that Speed Class write is defined to perform sequential writes to a completely un-fragmented area, and that a host may therefore fail to perform Speed Class recording even when unused memory exists in total — in which case the remedy is to rearrange the data or move it to another storage and re-format the card. Canon separately instructs formatting the card with the camera before recording movies, using Low level format before 8K or 4K, and says that when movies cannot be recorded properly you should format the card and try again. So: offload, format in the camera, and retest a correctly-marked card before concluding the card is too slow. Canon also suggests recording a few test movies at your chosen size to confirm the card keeps up.

What to look up on your own equipment

There is no universal answer, because the requirement is set per camera, per mode, and sometimes per bit depth. These are the exact places the three makers cited here publish it.

  • Sony: the online Help Guide page "Memory cards that can be used" for your model, split into "For still-image shooting", "For movie recording" and "For S&Q Motion shooting". Check the S&Q section separately even if you have already read the movie section. Read the asterisked footnotes under each table as well as the cells — on the a7 IV they change the requirement for 120fps slow motion and for XAVC S-I 4K at 60fps.
  • Canon: "Cards That Can Record Movies" under Movie Recording Quality — read its "Unsupported movie recording" list first — then "Card performance requirements (Movie recording)" in the Reference chapter for the per-mode SD table. For CFexpress detail per quality level, Canon's manual points to the Canon website rather than listing it inline.
  • Fujifilm: the per-camera compatibility page on fujifilm-x.com, which states the bitrate-to-class rules and also carries a per-camera card list for that body.
  • On the card itself: the class marks are printed on the label, and the bus generation is visible on the back. A single row of contacts means the card cannot be UHS-II or faster, so it cannot legitimately be V60 or V90. Two rows means it can. Check the capacity tier on the label too, alongside the class mark.
  • If you shoot microSD: the class marks and bus modes on this page are the same system — the SD Association applies UHS-I, UHS-II, UHS-III and SD Express to SDHC, SDXC and SDUC cards, and defines an SD Express microSD spec version. What differs is the physical card and the adapter. Sony's a7 IV help guide, for example, instructs that when using microSD cards with the camera you must use the appropriate adaptor. Confirm your own camera's note on adapters before relying on one for video.

Out of scope here: any claim about how a specific brand of card performs in practice, since that would require testing this publisher has not done. Also out of scope, on this site generally, are third-party adapters and undocumented combinations. If your open question is about glass rather than storage, see the lens mount guide for whether a lens will physically mount and keep autofocus, and the sensor format guide for reading a focal length and aperture across sensor sizes.

What this page does not tell you

  • Nothing on this page was tested or measured by the publisher. Every speed figure is reproduced from a standards body, a camera maker's own document, or SanDisk's support documentation, and the citation names the exact page read and the date it was read.
  • The manufacturer tables reproduced here are for three specific bodies — the Sony a7 IV (ILCE-7M4), the Canon EOS R5 and the Fujifilm X-T5. They do not transfer to other models, including other models from the same maker. Requirements are set per camera, per recording mode, and on the R5 per bit depth.
  • This page cannot tell you why a maker's required class exceeds the arithmetic from its own stated bitrate, or why the margin ranges from 1.2x to 3.2x across the published cases. The makers publish the requirement, not the reasoning. Use the division by eight only to rule cards out, never to rule one in.
  • Canon's own documentation is internally inconsistent about one mode on the EOS R5. Its Shooting chapter lists 4K 59.94/50.00 fps among the modes that cannot be recorded to SD at all, without naming a compression method; its Reference table dashes only the ALL-I variant and publishes SD classes for IPB and IPB (Light). This publisher cannot say which page reflects current firmware, and has not tested the camera. If that mode matters to you, verify it on your own body before buying an SD card for it.
  • What an SD Express card does in a UHS-II or UHS-I host is not stated on either SD Association page read here, and SanDisk's fallback statement covers UHS-II cards only. If you are considering an SD Express card for a UHS-II body, get that answer from the card maker for your specific card before buying.
  • Class marks are minimum speeds promised for a card in good condition on a compatible bus. They do not predict how a particular card behaves once it is heavily fragmented, nor how any specific brand or production batch performs; that would require testing this publisher has not done.
  • Manufacturer requirement tables change with firmware, and new recording modes can arrive with new card requirements. Re-check your own camera's current manual rather than relying on a table copied at a point in time.
  • Retailer product listings and marketing copy were not used to establish any technical claim on this page.

Check it on your own equipment

These go to the makers and standards bodies this page draws on, so you can look up your exact model.

  • Standards referenceSD Association: Speed Class reference

    The four class systems with their members, which bus family each mark may be applied to (including that V60 and V90 are UHS-II/UHS-III only), and the warning — in the 'Best Combination' section — that mixing class systems between host and card does not deliver the expected write speed. The fragmentation section at the bottom is what to read before blaming a card.

    www.sdcard.org
  • Standards referenceCompactFlash Association: Video Performance Guarantee (VPG)

    The definition of VPG and of minimum sustained write speed, and — in the note under the profile table and again in the FAQ — the statement that VPG-5 is not backward compatible with VPG-4, so a VPG800 or VPG1600 card will not necessarily work in a mode requiring VPG200 or VPG400. Read this before buying any CFexpress card for video.

    compactflash.org
  • Standards referenceCompactFlash Association: List of VPG-Certified Cards

    A searchable table of cards that passed CFA's certification protocol, with separate columns for the VPG-4 classes (200, 400) and the VPG-5 classes (800, 1600), plus company, card type, capacity, product name and part number. Check a part number here before you buy: the Association warns that some companies use the VPG logo without certification. This is a certification registry, not a ranking or a recommendation.

    compactflash.org
  • Manufacturer specificationCanon EOS R5 manual: Card performance requirements (Movie recording)

    Canon's full per-mode table, with separate 8 bit and 10 bit SD columns and a single CFexpress column that reads "Refer to the Canon website" in every row. It covers rows this page does not reproduce, including Full HD variants and time-lapse movies, and it is where you can check the 4K 59.94/50.00 fps IPB rows against the exclusion list in the Shooting chapter.

    cam.start.canon
  • Official support pageSony a7 IV Help Guide: Memory cards that can be used

    Sony's per-format card table split into still-image, movie recording and S&Q Motion sections, showing the different card requirements for the same bitrate in normal versus slow-motion recording, the two asterisked footnotes under the S&Q table, and the notes on CFexpress Type B and microSD adaptors. For your own body, search Sony's help guide index for your model and open its own 'Memory cards that can be used' page — the URL differs per camera in both path segments, so editing this one will not work.

    helpguide.sony.net

More questions

Sources

Every figure on this page comes from one of these 13 documents. Makers revise their specifications, so each is dated: open it before you buy.

  1. Speed Class - SD Association www.sdcard.org, Sep 22, 2026
  2. Difference between Speed Class, UHS Speed Class, Speed Ratings (Performance) | SanDisk support-en.sandisk.com, Sep 22, 2026
  3. X-T5 Compatibility - Fujifilm X www.fujifilm-x.com, Sep 22, 2026
  4. Bus Speed (Default Speed, High Speed, UHS, SD Express) - SD Association www.sdcard.org, Sep 22, 2026
  5. Specifications and Compatibility for SD/SDHC/SDXC Memory Cards | SanDisk support-en.sandisk.com, Sep 22, 2026
  6. Memory cards that can be used - Sony ILCE-7M4 Help Guide helpguide.sony.net, Sep 22, 2026
  7. Card Types - CompactFlash Association compactflash.org, Sep 22, 2026
  8. Video Performance Guarantee (VPG) - CompactFlash Association compactflash.org, Sep 22, 2026
  9. List of VPG-Certified Cards - CompactFlash Association compactflash.org, Sep 22, 2026
  10. Canon EOS R5 Product Manual — Compatible Cards cam.start.canon, Sep 22, 2026
  11. Canon EOS R5 Product Manual — Cards That Can Record Movies cam.start.canon, Sep 22, 2026
  12. Canon EOS R5 Product Manual — Specifications (Card performance requirements) cam.start.canon, Sep 22, 2026
  13. Canon EOS R5 Product Manual — Cautions for Movie Recording cam.start.canon, Sep 22, 2026